Mesh Coils

Pack of 2 replacement pods for the Aspire AVP.

The 2ml capacity pod is held in place into the main body of the AVP with magnets, and the 1.2ohm coil is set/fixed into the bottom fill pod, which is not replaceable/removable.

Pre installed, non replaceable 1.2ohm Ni-Chrome coil.  With the coil being Ni-Chrome this will enhance battery life as it doesn’t need the ramp up time that a standard kanthal coil does.

A replacement pack of 1 coil for the Aspire Cleito 120 tank. These Aspire Cleito 120 coils can handle up to 160 watts of power and are available in 0.16ohm & 0.15 Mesh resistance.
The Cleito 120 Coils are only compatible with the Cleito 120 Tank, and cannot be used with the original Cleito.

0.16 (100-120W)

0.15 Mesh (120-160W)

Designed mainly for flavour, Eleaf GS Air Coil Atomiser Heads operate at low to mid power variable wattage settings. GS Air coils come pre-fitted and packaged with a wide range of Eleaf starter kits and atomisers

While the GS Air coil range focuses mainly on mouth-to-lung (MTL) vaping styles, some vapers turn up the wattage and increase the airflow for a relaxed, direct-lung inhale. Whichever vape style you choose, GS Air coils offer great performance, with the added benefits of reduced e juice and battery power consumption.

There are currently three different resistances on offer in the GS coil range. All GS coils feature Kanthal coil wire and flavour enhancing, organic cotton wicks. The 1.5 Ohm coil features dual, parallel wound coil wire for a superbly satisfying mouth-to-lung vape.

Choose your preferred GS Air coil format from one of these options:


Eleaf GS Air 0.75 Ohm Coil Features:
Screw-in, replacement GS Air coil with a resistance of 0.75 Ohms
Designed for use with GS Air, GS Air-M, and GS Tanks
Features single Kanthal coil wire (not suitable for temperature control modes)
Traditional Stainless Steel, vertical coil format
Rated to fire between 8 & 25 Watts
Coil wrapped in a pure, organic cotton wick
Great flavour for an MTL or tight direct lung inhale
100% genuine replacement Eleaf coil


Eleaf GS Air 1.2 Ohm Coil Features:
Replacement, screw-fitted GS Air coil with a resistance of 1.2 Ohms
Suitable for use with GS Air, GS Air-M, and GS Tanks
Single Kanthal coil wire core (not compatible with temperature control modes)
Stainless Steel barrel, vertical coil format
Rated to fire between 8 & 30 Watts
Flavour enhancing, organic cotton wick
Capable of firing at a slightly higher wattage
100% authentic replacement Eleaf coil


Eleaf GS Air 1.5 Ohm Coil Features:
Screw-in low wattage GS Air coil with a resistance of 1.5 Ohms
Manufactured for use with Eleaf’s GS Air, GS Air-M, and GS Tanks
2 x parallel Kanthal coil wires (not compatible with temperature control modes)
Vertical coil format in a compact, Stainless Steel barrel
Rated to fire between 8 & 20 Watts
Wicked with pure organic cotton
Great flavour from a dual, parallel coil core
100% genuine Eleaf coil

Eleaf GS Air 0.35 Ohm Coil
The 0.35ohm coils are mesh, the first GS atomiser head to utilise this technology. It provides a sub-ohm coil, with large surface area. This means great clouds of vapour and outstanding flavour

The GT coils are designed for simplicity. They use a push-fit mechanism making the process of changing the coil both cleaner and easier.

With the option of a GT M 0.6ohm mesh coil or a 1.2ohm coil, both vapers who prefer larger clouds and those who prefer a restricted draw are catered for.

The sub-ohm HW-N and HW-M atomizer heads are great for vapers who like to directly inhale and create large clouds of vapour thanks to their mesh coils.

HW-M 0.15ohm (50-100W)

HW-N 0.2ohm (40-90W)

Compatible with both the Freemax Fireluke Mesh tank and the Freemax Mesh Pro tank, these coil options provide a new and improved wicking system along with new double and triple mesh coils. 

These coils are designed to provide a top tier vaping experience, with high volume vapour production and incredible flavour with every puff. You'll get more puffs out of them too, as the new wicking system keeps the cotton from drying out, ensuring greater longevity.

Specifications:

• Kanthal Single Mesh - 0.15ohm (40 - 70W)
• SS316L Single Mesh - 0.12ohm (400°F - 550°F TC)
• Kanthal Double Mesh - 0.2ohm (60-90W)
• Kanthal Triple Mesh - 0.15ohm (80 - 110W)

The FreeMax M Pro 2 Coils are an innovative product which has been designed for the ultimate flavour. They are compatible with the FreeMax Mesh Pro Tank which can endure a longer life span, compared to normal sub ohm coils. Flax and normal cotton feature within these coils.

These coils can be set to a higher wattage and produce larger clouds, ideal for all the vapers who enjoy sub-ohming.

Compatible with the following FreeMax products:

• M Pro Tank
• M Pro 2 Tank

The box comes with a scratch sticker so you can check the authenticity of this item.

FreeMax coils in this series:

• 904L M1 – 0.15Ω Ohm – 40-60W, best 65W (mesh)
• 904L M2 – 0.2Ω Ohm – 60-90W, best 80W (mesh)
• 904L M3 – 0.15Ω Ohm – 80-110W, best 100W (mesh)
• 904L M4 – 0.15Ω Ohm – 70-110W, best 95W (mesh)

The Fireluke M Twister coils are compatible with the Fireluke 2 Tank and Freemax Twister Kit. Designed for sub ohm vaping, these coils work best with high VG e-liquids that are 60% VG and higher.

Each variant features a mesh coil build, mesh has a larger surface area overall for faster heating and a reduced chance of hot spots. The TX coils use specially crafted tea cotton fibre wicks. These wicks absorb more eliquid and are 100% organic for a cleaner taste.

The coil types available, are the following:

The TX1 Mesh coils use a single Kanthal mesh build. Registering a 0.15 Ohm resistance, they should be used between 40 - 90W.

The TX3 Mesh coils have a triple Kanthal mesh build. Registering a 0.15 Ohm resistance, they should be used between 50 - 90W.

The TX4 Mesh coils utilise a quadruple Kanthal mesh build. Registering a 0.15 Ohm resistance, they should be used between 40 - 80W.

The TX1 SS316L coils use a Stainless Steel mesh coil build, meaning this coil can be used in Temperature Control and Variable Wattage mode. Registering a 0.12 Ohm resistance and can be used up to 60W.

The TNX2 coils feature a dual Kanthal mesh coil build. Registering a 0.5 Ohm resistance, these coils can be used between 20 - 50W.

The X1 coils feature a 0.15 Ohm resistance and utilise a single Kanthal mesh coil build. These coils should be used between 40 - 90W.

The X2 uses dual Kanthal mesh builds and registers a 0.2 Ohm resistance. These coils should be used between 40 - 80W.

The X3 has three Kanthal mesh coil builds and features a 0.15 Ohm resistance. These coils should be used between 50 - 90W

Geekvape have sat high in the ranks in the UK for years now, consistently bringing us top quality mods, tanks and RDA's that become fan favourites worldwide. Now with the release of the Geek vape Zeus Sub-Ohm Tank with the Z1 & Z2 coil they've created something astounding once again.

Mesh Z1 & Z2 Coils
These are the Geekvape Mesh Z1 & Z2 coils, a full flavoured mesh coil that are made for the Geekvape Zeus Tank. They promise crisp and rich flavour with dense cloud production. We sell these coils is packs of 5.

Improved airflow
Geekvape Zeus Z1 & Z2 coils have now improved the airflow control to boost flavour to the absolute maximum with this new Zeus Tank and the new coils are great to accompany this change perfectly

• Mesh Z1 Coil - 0.4ohm KA1 Mesh 60w - 70w
• Mesh Z2 Coil - 0.2ohm KA1 Mesh 70w - 80w 

Smok Nord Replacement Coils for the Nord vape kit feature a special atomizer structure that offers a dynamic vapour experience. Available in three atomizer types. Inclusive of a 0.6ohm Mesh Coil, a 1.4ohm Ceramic Coil and a 1.4ohm Traditional Coil.

Specifications:

0.6ohm Nord Mesh Coils - Optimised for Sub-Ohm Experience
1.4ohm Nord Regular Coils - Optimised for MTL Experience
0.6ohm Nord Regular DC Coils
0.8ohm Nord Mesh Coils - MTL
1.4ohm Nord Ceramic Coils
0.8ohm Nord DC MTL Coils

SMOK RPM Coils (5-Pack), a series of coils and RBA crafted for the SMOK RPM40, with the new 0.4ohm Mesh Coil, 0.6ohm Triple Coils, 1.2ohm Quartz and compatibility with the SMOK Nord Coil Series.

Features:

0.4ohm RPM Mesh Coil - rated at 25W
0.6ohm RPM Triple Coil - rated at 25W
1.0ohm RPM SC Coil - rated at 14W
1.2ohm RPM Quartz Coil - rated at 12W
0.3ohm RPM MTL Mesh

RPM & Nord Pod Options
Compatible with RPM or Nord Coils, respectively.
Compatible with SMOK Fetch Mini 40W Pod System

• High-Quality Stainless Steel Mesh
• Deep, Rich Cloud Taste
• Q4 Coil - 0.4ohm - Quadruple (40-100w / Best 60-80w)
• X6 Coil - 0.15ohm - Sextuple (50-120w / Best 80-100w)
• M4 Coil - 0.17ohm - Quadruple (30-70w / Best 40-60w)
• T10 Coil - 0.12ohm - Decuple (60-120w / Best 80-110w)
• X2 - 0.4ohm - Clapton - (40-80w / Best 60-70w)
• Mesh - 0.15ohm - Mesh (40-80w / Best 60-70w)
• Strip - 0.15ohm Mesh (40-100w / Best 80-90w)
• Max Mesh - 0.17ohm (80-130w / Best 90-110w)
• Daul Mesh - 0.2ohm  (50-80w / Best 65-75w)
• Triple Mesh - 0.15ohm (60-100 / Best 80-90w)

The SMOK Trinity Alpha Replacement Pod Cartridges are smartly designed 2ml refillable pods built with an air-driven design, MTL drip tip, and convenient threaded top-fill cap that utilises the SMOK NORD Coils. Each pack contains one Trinity Alpha Pod, one 0.6ohm NORD Mesh Coil, and one 0.8ohm NORD MTL Coil.

Features:

• Utilises the SMOK NORD Coil System
• 2ml Refillable Pod Cartridge Design
• MTL Delrin Drip Tip
• Air-Driven Design
• Organic Cotton
• Proprietary Pod Cartridge Installation

Uwell Caliburn G Pod Cartridge is a set replacement vape pods that design for Uwell Caliburn G Pod System Kit. It is made of PCTG and can hold up to 2ml of e-liquid.

Each pod is refillable and thanks to its top-fill design, you can fill e-juice stress-free. Remove the mouthpiece cap to expose the filling port.

The Caliburn G pods are compatible with the Uwell Caliburn G coils (not include) and can easily be removed and replaced to suit your needs.

The Uwell Crown III replacement coils have been designed for use with the Crown III vape tank only. For best results, we recommend pairing these coil with high VG liquids that are 60% VG or higher.

0.23 UN2 Mesh (65-75W)

0.25 (80-90W)

0.4 A1 (55-65W)

0.5 (70-80W)

The Uwell Crown 4 coils have been designed for use with the Uwell Crown 4 Tank only. There are four versions of this coil available, all of which have been designed for sub ohm vaping.

The 0.2 Ohm and 0.4 Ohm uses Stainless Steel (SS904L) rather than standard Kanthal, These coils heat faster and increase both flavour and cloud production. The 0.23 Ohm UN2 and 0.25 Ohm UN1 coils feature a mesh build that has a larger surface area for increased flavour.

All of these coils are recommended for use with high VG eliquids, that are 60% VG or higher.

The Uwell Crown 5 coils are an innovative collection of replacement coils, designed specifically for the Uwell Crown 5 Tank.

Each coil is made from premium materials with an innovative mesh design. The mesh design increases the surface area of the coil, enhancing e-liquid absorption and improving flavour and cloud production. 

• The 0.23ohm single mesh coil provides excellent, smooth flavour with impressive cloud production. We recommend using this coil on a power output of 65-70W.
  
  
• The 0.3ohm dual mesh coil is best for an output of 50-55W, and is also suitable for sub-ohm vaping, providing warm vapour and supreme flavour.
  
  
• The 0.2ohm triple mesh coil is best used at 65-70W, providing the most cloud production without drastically hampering the flavour. 

Replacing the coils is easier than ever thanks to the tank's plug'N'play design. Simply remove the old coil from the base of the Crown 5 tank, slide the new one in and you're done.

The Uwell Valyrian 2 coils have been designed for use with the Valyrian 2 Tank. There are four versions of this coil available, all of which have been designed for sub ohm vaping.
Pack of 2 coils

Features:

• Designed for sub ohm vaping
• Compatible with high VG e-liquids
• Mesh coil builds

The 0.32 Ohm Single UN2 coil features a single mesh coil build and has been built to maximise airflow. This coil can be used between 90 - 100W and the mesh has a larger surface area to heat more eliquid at a faster rate.

The 0.14 Ohm Dual Mesh UN2 coil utilises two mesh coil builds and has been created for enhanced cloud production. This coil can be used between 80 - 90W and the two mesh coil help create better flavour.

The 0.16 Ohm Triple UN2 coil features a triple mesh coil build and has been manufactured to deliver better flavour from your eliquids. Designed for use between 90-100W you’ll also experience increased vapour production.

The 0.15 Ohm Quadruple UN2 coil uses standard wound coils and features a quadruple coil build. This coil offers a balance of flavour and cloud and can be used up to 120W.

GT Core Coils by Vaporesso is a sub-ohm vape coil with multiple coil builds designed for use with high VG e-liquids.

The standard coils use Kanthal wire and organic cotton, working at a range of wattages to suit your vaping style. The CCELL coils use ceramic materials which reduce spit back and the chance of dry hits. The mesh coils have a larger surface area which in turn increases the amount of e-liquid is heated, for a boost in flavour.

As these coils are recommended for sub-ohm vaping, they are most compatible with high VG e-liquids, that is 60% VG and higher.

Coil Specification:

• Vaporesso GT2 0.4 Ohm Coil – single coil build – 40 to 80W

• Vaporesso GT4 0.15 Ohm Coil – dual coil build – 30 to 70W

• Vaporesso GT6 0.2 Ohm Coil - Triple coil build - 50 to 130W
  
  

• Vaporesso GT8 0.15 Ohm Coil – multi-coil build – 50 to 110W

• Vaporesso GT CCELL 0.5 Ohm Coil - Ceramic Coil Build - 15 to 40W

• Vaporesso GT CCELL 2 0.3 Ohm Coil – ceramic coil build – 35 to 40W

• Vaporesso GT Meshed 0.18 Ohm Coil – mesh coil build – 50 to 85W.

For use with PM80

Vaporesso GTX Coils are designed for the Target range of Vaporesso kits, including the Target PM30. Available in both standard and mesh builds, GTX coils can be used for mouth-to-lung or direct-to-lung vaping. Currently, two variants are available: 0.6ohm Mesh and 1.2ohm. 

Vaporesso GTX 0.6ohm coils provide more vapour, warmer flavour and can be used with higher VG e-liquids, ideally between 50-70% VG. These coils are also fully compatible with nicotine salt and standard (freebase) nicotine liquids. 

Vaporesso GTX 1.2ohm coils offer a thinner, more discreet cloud and slightly sharper flavour. 1.2ohm coils work best with 50:50 liquids or those with a higher PG ratio and are fully compatible with nicotine salt and standard (freebase) nicotine liquids. 

OC Coils by Vaporesso is replacement Vaporesso Orca Solo and the Vaporesso Orca Solo plus.

These coils use patented cCell ceramic materials for purer flavour and longer lasting coils.

Coil Specification:

• Vaporesso OC Mesh 0.6ohm Coil designed only for Orca Solo Plus Kit

• Vaporesso OC CCELL 1.3ohm Coil designed for Orca Solo Kit and Orca Solo Plus Kit.

GT Core Coils by Vaporesso is a sub-ohm vape coil with multiple coil builds designed for use with high VG e-liquids.

The standard coils use Kanthal wire and organic cotton, working at a range of wattages to suit your vaping style. The CCELL coils use ceramic materials which reduce spit back and the chance of dry hits. The mesh coils have a larger surface area which in turn increases the amount of e-liquid is heated, for a boost in flavour.

As these coils are recommended for sub-ohm vaping, they are most compatible with high VG e-liquids, that is 60% VG and higher.

Coil Specification:

• Vaporesso GT2 0.4 Ohm Coil – single coil build – 40 to 80W

• Vaporesso GT4 0.15 Ohm Coil – dual coil build – 30 to 70W

• Vaporesso GT6 0.2 Ohm Coil - Triple coil build - 50 to 130W
  
  

• Vaporesso GT8 0.15 Ohm Coil – multi-coil build – 50 to 110W

• Vaporesso GT CCELL 0.5 Ohm Coil - Ceramic Coil Build - 15 to 40W

• Vaporesso GT CCELL 2 0.3 Ohm Coil – ceramic coil build – 35 to 40W

• Vaporesso GT Meshed 0.18 Ohm Coil – mesh coil build – 50 to 85W.

P1 Coils by Vaptio designed for Vaptio Solo 2 AIO Kit. These coils are perfect for the Vaptio tanks. The coils use Organic Cotton Coils available in 0.5ohm and 0.15ohm resistance and also use mesh coil available in 0.2ohm